HVAC System Replacement in Katy & Fulshear, TX

Q: What about my existing ductwork?

We repair or modify ducts only if airflow measurements or visible condition requires it. We don't change ducts without cause.

Q: How long does a system replacement take?

Typically one day for a standard split system. More if ductwork modifications or electrical upgrades are needed.

Q: Do you handle permits and disposal?

Yes. We pull required permits, schedule inspections, and handle proper disposal including refrigerant recovery.

Q: What brands do you install?

We install quality equipment from trusted manufacturers. We'll discuss options that fit your needs and budget during your consultation.

Q: Do you offer financing?

Yes! We partner with Hearth Financing to offer flexible payment options for HVAC system replacements. Check rates in minutes with no impact to your credit score.

The Right Equipment. The Right Size. Documented From Start to Finish.

When repair costs exceed value or your system has reached the end of its life, we provide right-sized equipment recommendations with documented installation every step of the way. No overselling. No undersizing. Just the right solution for your home.

Free Estimates Proper Load Calculations Documented Installation 💰 Financing Available

Signs It May Be Time for a New System

Not every breakdown means replacement. Here are legitimate reasons we may recommend a new system—each must be documented.

Age & Performance

Equipment beyond typical service life (15-20 years)
Declining performance despite maintenance
Rising energy bills compared to prior seasons

Major Component Failure

Failed compressor or heat exchanger
Major refrigerant leaks or obsolete refrigerant (R-22)
Repair cost exceeds 50% of replacement value

Comfort Problems

Uneven temperatures that can't be corrected
System too small or large for current needs
Frequent breakdowns or repeated part failures

Our Replacement Process

From initial assessment to final testing, every step is documented so you know exactly what's happening.

1

Assessment & Documentation

We inspect your existing equipment (model, serial, condition, age), check duct condition and sizing, and document any leaks, corrosion, safety concerns, or failed components with photos.

2

Load Calculation & Sizing

We consider your home's square footage, insulation, windows, and layout to recommend properly sized equipment. Oversized systems short-cycle and waste energy; undersized systems can't keep up.

3

Equipment Selection

We present options based on your needs and budget—efficiency levels, features, and warranty coverage. We explain the differences so you can make an informed decision.

4

Professional Installation

Complete removal of old equipment, installation of new matched system, and any necessary updates to electrical, line sets, or condensate management. Every step is documented.

5

Testing & Handoff

System startup, testing, and verification of proper operation. We register your warranty, walk you through the thermostat, and provide documentation of the entire installation.

What's Included in Your Replacement

Matched Equipment

Outdoor unit, indoor coil/air handler, and thermostat designed to work together for optimal performance.

Permits & Disposal

We handle required permits and proper disposal of old equipment, including refrigerant recovery.

Warranty Registration

We register your equipment with the manufacturer to ensure full warranty coverage and support.

Photo Documentation

Before, during, and after photos of the entire installation so you have a complete record.

What We Will NOT Sell You

Replacement should be a solution, not a sales opportunity. Here's what we refuse to do:

❌ Oversized equipment without load/duct support

❌ Duct changes without measured or visible need

❌ Add-on products without documented issues they address

❌ Replacement when repair is practical and cost-effective

Frequently Asked Questions

How do you decide on system size?

We consider your home's square footage, insulation levels, window exposure, and existing duct capacity. Oversized equipment short-cycles (turns on and off frequently), wastes energy, and doesn't dehumidify properly. We avoid oversizing.

Do you reuse existing line sets?

Only if condition and compatibility allow. We inspect the existing line set for damage, proper sizing, and cleanliness. If it's compatible with the new system and in good condition, reusing it can save money. Otherwise, we replace it.

What about my existing ductwork?

We inspect your ducts and repair or modify them only if airflow measurements or visible condition requires it. We don't change ducts without cause—but if your ducts are undersized, damaged, or leaking, we'll document the issues and explain your options.

How long does a system replacement take?

A standard split system replacement typically takes one day. More complex jobs involving ductwork modifications, electrical upgrades, or difficult access may take longer. We'll give you a realistic timeline during your estimate.

Do you handle permits and disposal?

Yes. We pull required permits, schedule inspections when applicable, and handle proper disposal of old equipment including refrigerant recovery. It's all included in our quote.

What brands do you install?

We install quality equipment from trusted manufacturers. During your consultation, we'll discuss options that fit your needs and budget—different efficiency levels, features, and warranty terms.

Do you offer financing?

Yes! We've partnered with Hearth Financing to offer flexible payment options. Check rates in minutes with no impact to your credit score. Learn more about financing options →

See What We See

We document the condition of your old system, every installation step, all tests performed, and final readings with photos and video. You see what we see before and after the replacement—every recommendation is evidence-based.

Ready for a Free Replacement Estimate?

No pressure. No games. Just honest answers about whether replacement makes sense for your home.

📞 Call Now: 832-403-7466 Request Estimate